Electrical Test Calibrator Model 3200B

Electrical Test Calibrator Model 3200B

  • Fast, Safe, and Cost Effective Calibrations
  • Eliminates the Risk of Shock to the Operator
  • Eliminates Incorrect Connection Causing UUT Damage
  • Reduced Uncertainty for Loop Impedance Calibrations
  • Faster Calibration with Easier Connections
OVERVIEWOPTIONSVIDEOSDOWNLOADS

FAST, EFFICIENT ELECTRICAL TESTER CALIBRATION

The industry established 3200 Series provides by far the fastest solution for the calibration of Loop & RCD testers, PATs and insulationa testers and also one of the safest solutiuons for calibrtating hipot/breakdown testers.
Traditional testing practices required many items of test equipment and potential exposure to hazardous voltages with a typical multi function tester taking up to 45 minutes to calibrate.Using the 3200, calibration can be dramatically reduced to typically 15 minutes enabling safe, cost effective calibration to be put into practice, offering fast return on investment.
Dedicated mains sockets for Loop, RCD & PAT testers on the 3200 front panel avoid the need to make connection of mains/line voltages using 4mm type test leads. This important safety feature eliminates the risk of shock to the engineer as connections are made with standard mains/line plugs.Loop and RCD testers can simply be plugged directly into the dedictaed front panel mains/line socket – the advantages of this are:The 3200 has been designed from the outset as a high accuracy reference for the testing of electrical test equipment. Its accuracy provides a superior stand-off ratio of better than 4:1 – essential for accurate, repeatable testing.

IDEAL FOR ON SITE CALIBRATION

The 3200 also offers a robust, transportable design ideal for on-site calibration work. The lightweight (20 lb) calibrator can be supplied with a custom soft carrycase. The AutoLoop option also provides the capability to measurement local line impedance for the complete on-site solution.

PRODUCT FEATURES

Designed for use on protected supplies – no dedicated supply required.

Built-in Unit Under Test (UUT) fault detection – avoids further damage to UUT and protects calibrator

Autoloop option to automatically measure and correct loop resistance values

Designed for international support – uses dedicated custom socket on the front panel for multiple regions

Dedicated function keys for each function for easy & intuitive operation

Robust & lightweight design ideal for on-site calibration.
Autoloop option allows line impedance compensation.

TRANSMILLE’S 3000 SERIES CALIBRATES;

INSULATION TESTERS (TO 5kV)
HIPOT/BREAKDOWN TESTERS
EARTH BOND TESTERS TO 30A
RCD/RCCB TESTERS
HV SOURCES
LOOP TESTERS
PORTABLE APPLIANCE TESTERS
INSULATION TESTERS

FLASH TESTER ADAPTOR, CLASS 1 & 2

HIGH RESISTANCE ADAPTOR (15kV)

HIPOT TESTER ADAPTOR

HIGH ACCURACY RESISTANCE OPTION

10GOhm INSULATION RESISTANCE OPTION

AUTOLOOP LINE IMPEDANCE COMPENSATION

EXTERNAL RESISTOR & REAR TERMINALS

 

OPTION FLASH

The flash test adapter option provides a fast, safe and easy method for measuring PAT flash voltage and current at CLASS 1 and CLASS 2 settings. The design of the flash test adapter allows direct connection of the PAT flash probe, holding it down safely on the voltage input connector of the adapter.

OPTION HIRES

The high resistance multiplier adapter for the 3200 provides a low cost solution for the resistance calibration of some makes of high voltage (above 1kV) insulation testers avoiding the problem of obtaining high value, high resistance resistors.

The adapter both increases the test voltage at which the calibration can be performed*, and also increases the resistance range of the 3200 by a factor of 10. This allows the standard 3200 to be used for resistance calibration of testers up to 15kV at up to 200 GOhms. With the 10 GOhms option fitted to the 3200 values of up to 1 TOhm can be simulated.

* Note : Does not measurement test voltage

OPTION HIPOT

The hipot / breakdown tester adapter offers a unique solution to the safe, fast calibration of both voltage output and leakage current measurements on hipot and breakdown testers. Desinged to sit flat on the bench the high voltage probes, with a switch in the handle, often used with breakdown testers can be safely pressed down on the terminals.

The breakdown adapter provides 3kV & 12kV voltage measurement ranges for both AC and DC. LEDs indicate which terminal should be used.

To calibrate the output/leakage current display of the hipot / breakdown tester the adapter provides 9 high power resistors to provide current loads of up to 20mA @ 1000V – a function not available on other calibrators.

 

OPTION HIACC

Higher Accuracy – approximately 3 times better for the insulation resistance and continuity resistance
(NOT RETRO-FITTABLE)

 

OPTION 10G

Extends the resistance range for the standard 2G Ohms to 10G Ohms to cover calibration of insulation testers with higher ranges (RETRO-FITTABLE)

 

OPTION AUTOLOOP


The auto loop impedance measurement and correction function provides an easy way to measure the loop impedance and add this to the calibrated resistance values stored in the 3200.

At the press of a button, the 3200 measures the loop impedance of the supply it is connected to and adds this measured value to the calibrated value displayed when a loop resistance is selected. For example a measured loop impedance of 0.15 Ohms will result in a corrected value of the [calibrated value] + [0.15 Ohms].

This provides an accurate and repeatable method for calibrating loop testers even when calibrating on-site.

 

OPTION EXTRES

Add an additional two custom resistors to the available LOOP and PAT Earth Bond Resistance values via 4mm terminal input on the rear of the 3200 (RETRO-FITTABLE)

 

 

A demonstration of calibrating the Continuity Resistance function of an electrical tester using the Transmille 3200A Electrical Test Equipment Calibrator

A demonstration of calibrating the Insulation Resistance function of an electrical tester using the Transmille 3200A Electrical Test Equipment Calibrator

A demonstration of calibrating the Loop Resistance function of an electrical tester using the Transmille 3200A Electrical Test Equipment Calibrator
A demonstration of calibrating the RCD Trip Time & Current functions of an electrical tester using the Transmille 3200A Electrical Test Equipment Calibrator
PRODUCT VIDEO: 3200 OVERVIEW
PRODUCT VIDEO : CONTINUITY RESISTANCE
PRODUCT VIDEO : INSULATION RESISTANCE
PRODUCT VIDEO : LOOP RESISTANCE
PRODUCT VIDEO : RCD TRIP TIME & CURRENT

?
Live Chat Support Software